JN5189 MSK32W-M13 Middle Power ZigBee module with u-FL connector

Introduction 

The MSK32W-Myy module family provides designers with a ready-made component that provides a fully integrated solution for applications, using the NXP K32W061 series of chips they are ultra-low power, high performance Arm® Cortex ®-M4 based wireless microcontrollers supporting ZigBee 3.0, Thread and Bluetooth Low Energy 5.0 networking stacks to facilitate home and building automation, smart lighting, smart locks and sensor network applications. 

The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. 

Due to NXP K32W series chips provide following different options 

• K32W series - both support ZigBee and BLE with NFC option 

• JN5189 series - Support ZigBee only with NFC option 

• QN9090 series - Support BLE only with NFC option 

Module can be following different options 

• M10 - Support middle power with PCB antenna 

• M13 - Support middle power with u-FL connector 

• M16 - Support high power both PCB and u-FL connector diversity 

The Bluetooth and ZigBee can’t transmit at the same time, M16 only supports the ZigBee function. All modules have FCC, CE and Industry Canada modular approvals. The variants available are described below. 

Key features 

Radio 

• 2.4 GHz IEEE 802.15.4 2011 compliant 

• 2.4 GHz Bluetooth Low Energy 5.0 compliant 

• Receiver current 4.3 mA 

• IEEE 802.15.4 Receiver sensitivity -100 dBm 

• Bluetooth Low Energy 5.0 2 Mb/s high data rate 

• Bluetooth Low Energy Receiver sensitivity -97 dBm 

• Improved co-existence with WiFi 

• Configurable transmit power up to +10 dBm, with 46 dB range 

• Transmit power / current +9.5 dBm / 20.3 mA 

• Transmit power / current +2.5 dBm / 9.4 mA 

• Transmit power / current 0 dBm /7.4 mA 

• 1.9 V to 3.6 V supply voltage 

• Antenna Diversity control 

• u-FL connector or PCB antenna 

Microcontroller 

• Integrated ultra Low-power sleep oscillator 

• Deep Power-down current 350 n A (with wake-up on IO) 

• 128-bit, 192-bit or 256-bit AES security processor 

• MAC accelerator with packet for matting, CRCs, address check, auto-acks, timers 

• Application CPU, Arm Cortex-M 4 CPU 

• On-Chip memory: 640 KB flash; 152 KB SRAM 

• 12 MHz to 48 MHz system clock speed for low-power 

• 2 x I2C-bus interface, operate as either master or slave 

• 10xPWM 

• 2 x Low-power timers 

• 2 x USART, one with flow control 

• 2 x SPI-bus, master or slave 

• 1 x PDM digital audio interface 

• 19-channel DMA engine 

• Up to four GPIOs can be selected as pin interrupts 

• 32-bit Real Time clock (RTC) with 1 s resolution. 

Antenna Specification 

• MSK32WT-M13 use an external dipole antenna (u‐FL connector). Antenna Gain: 2.43 dBi  

• Modulation Type: O‐QPSK(ZigBee)/GFSK (BLE) 

• Frequency: 2405~2480MHz 

• CH Numbers: step 5MHz 

Benefits

• Very low current solution for long battery life 

• Single chip device to run stack and application 

• Flexible sensor interfacing 

• Optional Embedded NTAG 

• Lead-free and RoHS compliant 

• Junction temperature range: 40°C to+125°C 

Application 

• Zigbee 3.0, Thread networks 

• Bluetooth Low Energy 5.0 networks 

• Robust and secure low-power wireless applications 

• Smart lighting, door locks, thermostats and home automation 

• Wireless sensor networks 

Certification 

• FCC: 2AZ3DK32WM10 

• ISED: 27325-K32WM10 

• CE: Pass 

Technical Support: By phone or e-mail